baja designs light mount,hella light mount, la paz light mount, 3 hole light mount, 3 hole trick tab, lp9 mount, lp6 mount,lp4 mount, sol tek, weld on light mount, baja designs weld mount, baja designs trick tab

1/8" cnc formed 3 hole light mount tab. Works with all single and 3 hole Lights.Designed for 1 3/4" Tube - If shipping price is High I will refund the shipping offset when card is captured.

Note: minor radius modifications will work for other tube sizes

Weldable Mounting Tabs For Led Knockoff Lights. 2" tube. 1/4″ HR Steel. Comes in a set of 2.
Choose USPS Flat Rate at Checkout

Weldable Mounting Tabs for any single Bolt Mounted Led Light. Use for 1 3/4" Tube 1/4″ hr steel. Sold in set of 2.
Choose USPS Flat Rate at Checkout

Weldable Mounting Tabs for any single Bolt Mounted Led Light. Use for 2" Tube. 1/4″ hr steel. Sold in set of 2.
Choose USPS Flat Rate at Checkout

This kit comes with everything you need to replace your Current Bed Support Rodends
2- 3/8" NF RH Rodend
2- 3/8" NF LH Rodend
2- 3/8 NF RH Nuts
2- 3/8 NF LH Nuts

NOTE:
For Extreme Weather Conditions we recommend to coat the rod ends with a clear coat paint and Anti-Seize the threads. '
At Check Out Use flat rate envelope for shipping

baja designs onx6 weld on tabs, bajadesigns weld on tabs, bajadesigns weld, onx6 weld, onx6 weldable tabs, bd weldon, baja designs weld on mounts, baja design, weldable baja

Allows you to Mount the ONX6 Straight out. Comes with 3/8″ Stainless Hardware and Brackets are 304 SS. Sold in a set.
Choose USPS Flat Rate at Checkout

Kc Gravity Weld On Mounts for 1 3/4" tube. Make sure to use Flat Rate shipping at check out

Designed to mount the S2 lights in a protective 3/16″ Housing. The original Mounting design is mainly used for the Thuren High Clearance Bumper although these housings can be used to mount to any flat surface. Bolt on needs a 3″x7″ flat surface and the weld on uses a 3″ x 4″ flat surface.

Comes With all needed SS Hardware. Choose USPS Flat Rate at Checkout

Mount any Brand Led light up to 26″ to your 03-13 Dodge
Ram 2500/3500. It’s up to you where to mount the light and drill where
needed. Mounting Plate bolts on behind the tow hooks and comes non
painted. 3/8″ Grade 8 hardware included. If you ditch the tow hooks a 30″ LED will fit.

dodge ram backup light mounts, no drill ram backup light mounts

+14 dodge ram rear light brackets (No drill)

5th gen ram backup light brackets (No Drill)

Mount your 10″ or 20″ Baja Designs ONX6 in between your
bumper opening. Complete Bolt on behind Tow Hooks. Comes With new 3/8″
Stainless mounting Hardware. Mount is made out of 1/4″ steel and 2 stage
Powder Coated Black. USA Made!

Mount your Rigid or Knockoff 10″ or 20″ LED in between your bumper opening. Complete Bolt on behind Tow Hooks. Comes With new 3/8″ Stainless mounting Hardware. Mount is made out of 1/4″ steel and 2 stage Powder Coated Black. USA Made!

Long Travel Traction Frame Brackets. Made out of a 3/16 P&O HR. Machined, Mig welded and Blended. Sold as a Pair

• For 2500/3500 03-18 Dodge Rams
• Bolts Under Tow Hooks, No Drilling, 1/4 Cold Roll Steel Brackets, 1 3/4″ .120 wall Tubing, Laser Cut HID Light Tabs (Works for any Light), Mount UP to 9″ Lights, Comes With New Stainless Steel Bolts, Nylock Nuts.
  For 03-12 Dodge Rams,Doesn’t Fit Sport Models, Tow hooks still can be used, Although pulling to the left and right with both hooks at the same time is limited.

03-16 Dodge Curt Receiver Tow Hooks

For 2500/3500 03-18 Dodge Rams

Bolts Under Tow Hooks, No Drilling, 1/4 Cold Roll Steel Brackets, 1 3/4″ .120 wall Tubing, Laser Cut HID Light Tabs (Works for any Light), Mount UP to 9″ Lights, Comes With New Stainless Steel Bolts, Nylock Nuts.
For 03-12 Dodge Rams,Doesn’t Fit Sport Models, Tow hooks still can be used, Although pulling to the left and right with both hooks at the same time is limited.

ramdring, ram d-ring, 2500/3500 dring, dodge d ring, d-ring, pattonfab d rings, D-rings,

Pre-load bed support’s mount on the rear bed posts next to the tailgate with a drivers side flag mount.

Long Travel Traction Axle Brackets. Made out of a 3/16 P&O HR. Mig welded.
Long Travel Traction Frame Brackets. Made out of a 3/16 P&O HR. Machined, Mig welded and Blended. Sold as a complete set.

3-13 2500/3500 Dodge Ram 2 Tab All In One Light Bar

New Design. Lights sit with top of bumper and Reversed Tab’d for better light protection. The center of the light bar now has mounting holes to run a 10″/20″ LED. Current setup is for Baja Designs Stealth series.

Bolts Under Tow Hooks, No Drilling, 1/4 Laser Cut Steel Bracket, 1 3/4″ .120 Wall Tubing, Laser Cut HID Light Tabs (Works for any Light), Mount UP to 9″ Lights, Comes With New Stainless Steel Bolts, Nylock Nuts.

For 03-18 Dodge Rams,Doesn’t Fit Sport Models, Tow hooks still can be used, Although pulling to the left and right with both hooks at the same time is limited.

03-13 2500/3500 Dodge Ram All In One Light Bar

New Design. Lights sit with top of bumper and Reversed Tab’d for better light protection. The center of the light bar now has mounting holes to run a 10″/20″ LED. Current setup is for Baja Designs Stealth series

Bolts Under Tow Hooks, No Drilling, 1/4 Laser Cut Steel Bracket, 1 3/4″ .120 Wall Tubing, Laser Cut HID Light Tabs (Works for any Light), Mount UP to 9″ Lights, Comes With New Stainless Steel Bolts, Nylock Nuts.

For 03-15 SLT Dodge Rams,Doesn’t Fit Sport Models, Tow hooks still can be used, Although pulling to the left and right with both hooks at the same time is limited.

Made out of  Laser Cut HR 1/8″ & 3/16 plate. 1.25" Dom Tube Tig
Welded will act like a crush when
mounting with grade 8  1/2″ bolts. Fully bolt on. Inside the horn there
is .120 lower internal gusset and a 3/16" center gusset to help
support inner 2×2 tube and side support bars. Bottom plates and top
plates are 3/16″ thick. Designed to use a 2" top tube and mount up to a
30" led bar inside the light slot. Comes with front 3/16" front light
plate,lower skid mount support and hardware.

Made out of  Laser Cut HR 1/8″ & 3/16 plate. 1.25" Dom Tube Tig Welded will act like a crush when
mounting with grade 8  1/2″ bolts. Fully bolt on. Inside the horn there is .120 lower internal gusset and a 3/16" center gusset to help
support inner 2×2 tube and side support bars. Bottom plates and top
plates are 3/16″ thick. Designed to use a 2" top tube and mount up to a 30" led bar inside the light slot. Comes with front 3/16" front light plate,lower skid mount support and hardware.

2019 ram light bar, 2500 light bar, 5th gen light bar, 5th gen light bar, ram light bar,